Subscribe us to get the latest news!
Skip to content
: Trying to access array offset on value of type bool in /home/apkplaye/customeasy.org/wp-content/themes/flatsome/inc/shortcodes/ux_image.php
on line 60
RAPTOR Z – XY2 ARM
Feature the best ability of Raptor Z arm and Raptor XY2 collaboration!
BACK TO PRODUCT PAGE
- PAYLOAD: 8 – 30kgs (17 – 66lbs)
- Lift range: 56cm
- Weight: 14.6kgs/32.18 lbs
ATTENTION: PLEASE READ THIS BEFORE USING IT TO PREVENT SERIOUS DAMAGE TO THE GEAR!
- IT IS RECOMMENDED TO HAVE PROPER SPRING ADJUSTMENTS
For additional tension support, adjust both the spring sets to the same degree of tension.
- ALWAYS KEEP FINGERS CLEAR FROM ANY OF THE MECHANICAL MOVING PARTS
Operate the Arm from outside of any crossing arms and from the spring shaft.
- CAREFULLY TIGHTEN THE FASTENERS
When connected to scaffold tabes, ensure that all locking bolts and scaffold clamps are locked securely. It prevents breakage to the equipment & any harm to the crew. It also provides protection & stability.
WHAT’S IN THE BOX
Box 1: Raptor Z arm built -in Single Spring, Heavy Springs, Travel Case
Box 2: Raptor XY2, Mitchell Wrench, Travel Case
INSTALLATION AND ADJUSTMENT
Where to mount and configure Raptor Z – XY2?
- Step 1: Mount the arm to Speed rail (scaffold) 48 – 51mm
- Step 2: Install Arm to Female Mitchell
- Step 3: Install Raptor XY2
- Step 4: Install Vibration (if any) and Payload
- Step 5: Adjust Spring
- Step 6: Adjust Raptor Z arm Dampener
- Step 7: Lock or Unlock the Raptor XY2
- Step 8: Raptor XY2 damper adjust
Extra: Exchange the springs (from Single Springs to Heavy Springs and vice versa)
Mount the arm to Speed rail (scaffold) 48 – 51mm
Mounting the Raptor Z arm is as simple as clamping it to a standard 48 – 51mm Pole. Connect the Arm on Pole with two single clamps at the back of the arm. Other standard grip components such as Poles and clamps can be mixed to provide different vehicle mounting configurations.
Install Arm to Female Mitchell
Using M10x25 screws (in the box) to assemble Arm to Female Mitchell to Raptor Z arm.
Install Raptor XY2
Build in Raptor XY2 to Arm to Female Mitchell via Mitchell-based.
Install Vibration (if any) and Payload
Assemble Vibration and Payload to Raptor XY2 via Mitchell-based.
Loosen the locking nuts of each spring. Use a 13mm wrench (included), turn the leveling springs clockwise to add tension, and raise the arm; turning it anti-clockwise will release tension and lower it. After setting, re-lock the locking nuts of each spring.
NOTE: Adjust both springs equally. The correct position should be at 10-15 degrees
Adjust Raptor Z Arm Dampener
To smoothen Spring Tension, turn the adjustment knob. If the arm is too soft, turn it towards the direction of H (Hard). If the Arm is rigid, turn it towards the direction of S (Soft).
NOTE: The valves should always be adjusted evenly and set identically. Rebound and compression of the hydraulic valves should be put in such a way so that any loose swinging or vibration of the arm is eliminated.
Lock or Unlock the Raptor XY2
Rotate the knob clockwise or counterclockwise when you want to lock/unlock the movements of the X axis or Y axis, each axis has 2 knobs.
Raptor XY2 Damper Adjust
Rotate the knob clockwise or counterclockwise when you want to adjust the dampner to Hard (H) or Soft (S). And use allen key lock the screw to avoid the knob drifting during use.
NOTE: Don’t opent this screw as it is used to remove the knob (assembly)
HOW TO EXCHANGE THE SPRINGS
BLOG: GFStudio Rental house masters filmmaking with Custom Easy products.
FAQ: Can Raptor Z – XY2 work overslung?
Yes, Raptor Z – XY2 supports both underslung and overslung!
learn more faq